Parts & Accessories

Grade 10 chromium steel balls

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - Crafted from lightweight aluminum - End Cap Sold Separately - Weight: 39 g

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork. Kit includes Center Lock Adaptor, allowing riders to use 6-bolt rotors on Shimano Center Lock compatible hubs. - 6mm spacer kit adapts 142 x 12mm rear hub to 148 x 12mm - Includes 6mm adapter to 6-bolt rotors - Includes external spline lock ring for thru-axle compatibility

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag

Replacement freewheel spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - Fits around standard freewheel threads

The Stolen rim strip features 30mm width and 20" diameter. - Material: PVC - Wheel Size: 20" - Rim Strip Width (mm): 30 mm - Adhesive: No

Choose to ride even faster by using CeramicSpeed Hub Bearings in your wheels. The DT Swiss-3 wheel kit fits 240s Disc hubs. Other kits are available for DT 240s rim brake hubs, and DT180 as well. The high velocity of wheel bearings means that bearing friction can have a huge impact on performance. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard wheel bearings. In The Box: - 2 x 61903/18 bearings - 2 x 61802 bearings - 2 x 61902 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet Remember to add grease and mount seals before installation.

Get your WeThePeople Arrow Front Hub Axle/Cone Set and freshen up that front end that's a little wobbly after that last time you cased it on the spine.

Did you trash the front bearings on your WeThePeople Arrow front hub? It happens, that just means you're riding a lot. Fear not, we've got you covered with this bearing set from WeThePeople.

WeThePeople's Supreme Hub Guards are made of low-friction nylon fiberglass. Simply replace the cones on your Supreme Front and Cassette Hubs for a perfect fit without having to spread your dropouts. Available for both front and rear. These guards now feature a heat-treated chromoly insert for longer life.

The Rear Wheel Cover is a critical safety component for carrying passengers on the Globe Haul ST. The easy-to-install guards cover openings on the frame and rear rack to prevent fingers, toes, and clothes from getting too close to the moving wheel and chain. They also protect from dust and grease to keep riders and bikes cleaner. **For Globe Haul ST bike customers: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Compatible with Haul ST. - Includes two upper fender covers and two lower wheel covers. - Easy toolless installation.

- Kits include one pair of end caps - Instructions and hub axle determinations are available online @ www.notubes.com

- Replacement part for Surly hubs.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces

Authentic Ritchey hub conversion kit for mountain bike hubs. - Convert to 15mm thru-axle - End cap conversion for Vantage and Trail non 2-piece V2 hubs for 15mm thru axle

Replacement XD driver freehub body for Trail and Vantage 2-piece Ritchey hubs. - SRAM XD

Conversion kits and caps sets compatible with Ritchey front hubs. - For any Ritchey 15mm front thru-axle hub - Replacement endcap for Phantom Flange front hubs - Converts from 15mm TA to 9mm QR

Replacement axle and end cap for 2-piece rear disc road hubs - Retains original 12mm thru-axle set-up

Authentic service bearing kit for Ritchey mountain bike wheels. - Replacement bearings for Vantage V1 non-2pc hubs

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 155mm - 1 axle per bag

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.

DT Swiss tubeless ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type set ups. - Highly resistant adhesive tape works as a rim tape and airseal

End caps for front conversion hubs.

Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 40g