Parts & Accessories

Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap

Maxle Ultimate Lever Assembly - Fits Maxle Ultimate B1 - Includes lever section only - Suitable for suspension forks

The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - Weight: starting at 20g for 64 nipples

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread pitch: 12 x 1.5mm - Length: 121mm

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread Pitch: 12 x 1.0mm

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever

The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications

- Hub axle end cap set, rear - Zipp Cognition V2 Rim Brake - Quick release

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

Your riding doesn’t need to stop when the weather gets cold. Features - Giant road thru-axle trainer axle - Alloy construction - For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum

A few too many drops to flat? Get your Arrow Rear Hub back in solid working order with this replacement axle/cone set from WeThePeople.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Authentic service axle and end cap kits for Ritchey wheels and hubs. - Replacement axle for non-boost 2-piece disc hubs - Includes axle and end caps - No tools necessary

Replacement axle and end cap for 2-piece rear disc road hubs - Retains original 12mm thru-axle set-up

Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 44g

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs - Type: Solid Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 174mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 130mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 174mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Solid Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 155mm - 1 axle per bag